English
italiano
العربية
فارسی
Indonesia
हिन्दी
Melayu
русский
Tiếng Việt
ไทย
GE Fanuc IC698CPE010 Processor Module CPU
GE Fanuc IC698CPE010 Processor Module CPU 100% Brand New. 365 days warranty.
item no.:
IS200EXCSG1ABAlead time:
1-2 daysproduct orgin:
GERMANYshipping port:
Xiamenpayment:
T/TCondition:
NEW
GE IS200EXCSG1A FUNCTIONAL DESCRIPTION
IS200EXCSG1A is an Exciter Conduction Sensor Board manufactured and designed by General Electric as part of the EX2100 Series used in Excitation Control Systems. The EX2100 Excitation Control uses the IS200EXCS Conduction Sensor Board (EXCS) to detect bi-directional current flowing over a bus line. The IS200EGPA Exciter Gate Pulse Amplifier Board (EGPA) supplies the board with power, and it also filters the EXCS board's output before sending it to the IS200EMIO Exciter Main Input/Output Board (EMIO).
The EXCS board detects current using two unidirectional Hall Effect sensors facing opposite directions. Depending on the existence of a magnetic field, these sensors generate a logical output. A logical low output is generated by the circuit when either sensor detects a magnetic field that is greater than the operating threshold of the sensor (indicating current). When the field dips below the release point, the sensor will continue to operate in this low output mode.
GE IS200EXCSG1A Circuit Interconnect Diagram
The board has gapped steel rings affixed to it in order to monitor current flow. These circles are traversed by the bus route. The concentrated magnetic flux generated within the rings is measured by the Hall Effect sensors on the circuit board. The EXCS board is mounted directly to the bus line and the steel rings are held in place by a plastic mounting bracket.
A power supply input of +12.0 V dc 5%, 0.3 watts at most, and a 12 V dc return is needed for the EXCS board. The EGPA board is the source of these. For redundancy, the EGPA board receives two identical logical output signals from the EXCS board. Logic high outputs are above 11 V dc while logical low outputs are less than 1.2 V dc. The 4-pin P1 connector is used to connect all inputs and outputs to the EGPA board. Three EXCS boards, one for each bus line, are powered by the EGPA board. It transfers the information to the EMIO board after filtering the output signals from each of the EXCS boards.
The Power Conversion Module (PCM) cabinet holds the EXCS board, which is devoid of fuses, testpoints, LED indications, and movable hardware. P1 is the only 4-pin connector on the board.
GE Fanuc IC698CPE010 Processor Module CPU 100% Brand New. 365 days warranty.
GE Fanuc IC697CPX772 CENTRAL PROCESSO UNIT 100% Brand New. 365 days warranty.
GE Fanuc IC698CPE020 RX7i CPU MODULE 100% Brand New. 365 days warranty.
GE Fanuc IC693MDL645 Input Module NEW 100% Brand New. 365 days warranty.
GE Fanuc IC693CHS392 10-Slot Expansion Rack Controller 100% Brand New. 365 days warranty.
GE Fanuc IC693ALG223 input module PLC 100% Brand New. 365 days warranty.
GE Fanuc IC695CPU310 CPU PAC Systems RX3i Computer Accessorise 100% Brand New. 365 days warranty.
GE Fanuc IC693CMM321 Ethernet Controller CMM-321 100% Brand New. 365 days warranty.
To get lowest price with best original quality,pls don`t hesitate to leave a message here.Thank you!
Room 1904, No.96-2 Lujiang Road, Siming District, Xiamen (Building B of Diamond Coast)
