English
italiano
العربية
فارسی
Indonesia
हिन्दी
Melayu
русский
Tiếng Việt
ไทย
GE Fanuc IC698CPE010 Processor Module CPU
GE Fanuc IC698CPE010 Processor Module CPU 100% Brand New. 365 days warranty.
item no.:
IS200TBAOH1Clead time:
1-3 daysproduct orgin:
USAshipping port:
Xiamenpayment:
T/TCondition:
NewIS200TBAOH1C Specifications
Number of channels: 16 current output channels, single-ended (one side connected to common)
Analog output current: 0-20 mA
Customer load resistance: Up to 500 Ω burden with VOACH1B and TBAOH1B and 900 Ω burden (18 V compliance) with PAOC and IS200TBAOH1C
IS200TBAOH1C Physical
Size: 10.16 cm wide x 33.02 cm high (4.0 in x 13.0 in)
Temperature: -30 to +65ºC (-22 to +149 ºF)
IS200TBAOH1C Functional Description
The Analog Output IS200TBAOH1C terminal board supports 16 analog outputs with a current range of 0-20 mA.
Current outputs are generated by the I/O processor, which can be local (Mark* VIe control) or remote (Mark VI control).
The outputs have noise suppression circuitry to protect against surge and high-frequency noise.
TBAO has two barrier-type terminal blocks for customer wiring and six D-type cable connectors.
In Mark VI systems, IS200TBAOH1C works with VAOC processor and supports simplex and TMR applications.
Cables with molded plugs connect IS200TBAOH1C to the VME rack where the VAOC board is located.
In TMR systems, IS200TBAOH1C is cabled to three VOAC boards.
In Mark VIe systems, IS200TBAOH1C works with the PAOC I/O pack and supports simplex applications only.
The I/O packs plug into the D-type connectors and communicate over Ethernet with the controller.
IS200TBAOH1C Installation
Attach IS200TBAOH1C to a vertical mounting plate. Connect the wires for the 16 analog outputs directly to the two I/O terminal blocks mounted on the left of the board. Each point can accept two 3.0 mm (#12AWG) wires with 300 V insulation per point using spade or ring type lugs. Each block is held down with two screws and has 24 terminals. A shield terminal strip attached to chassis ground is located immediately to the left of each terminal block. Make cable connections to IS200TBAOH1C follows:
• In Mark VI systems, connect cables with molded plugs to the D-type connectors on the IS200TBAOH1C and to the VME rack where the VAOC processor is located. Use two cables for simplex or six cables for TMR.
• In Mark VIe systems, plug the PAOC I/O packs directly into selected D-type connectors. Special side mounting brackets support the packs.
IS200TBAOH1C Operation
IS200TBAOH1C supports 16 analog control outputs. Driven devices should not exceed a resistance of 500 Ω (900 Ω if using I/O packs) and can be located up to 300 m (984 ft) from the turbine control cabinet.
The VAOC or PAOC contains the D/A converter and drivers that generate the controlled currents. The output current is measured by the voltage drop across a resistor on the terminal board.
Filters reduce high-frequency noise and suppress surge on each output near the point of signal exit. The following figure shows IS200TBAOH1C in a simplex system.
GE Fanuc IC698CPE010 Processor Module CPU 100% Brand New. 365 days warranty.
GE Fanuc IC697CPX772 CENTRAL PROCESSO UNIT 100% Brand New. 365 days warranty.
GE Fanuc IC698CPE020 RX7i CPU MODULE 100% Brand New. 365 days warranty.
GE Fanuc IC693MDL645 Input Module NEW 100% Brand New. 365 days warranty.
GE Fanuc IC693CHS392 10-Slot Expansion Rack Controller 100% Brand New. 365 days warranty.
GE Fanuc IC693ALG223 input module PLC 100% Brand New. 365 days warranty.
GE Fanuc IC695CPU310 CPU PAC Systems RX3i Computer Accessorise 100% Brand New. 365 days warranty.
GE Fanuc IC693CMM321 Ethernet Controller CMM-321 100% Brand New. 365 days warranty.
To get lowest price with best original quality,pls don`t hesitate to leave a message here.Thank you!
Room 1904, No.96-2 Lujiang Road, Siming District, Xiamen (Building B of Diamond Coast)
